Monthly Archives: October 2015

BB-8 progress

Time for another update on my BB-8!

Things have been going well, and this week I printed the last pieces for the body:

IMG_9629

In all, that makes quite a large stack of pieces that I need to go through and sand and treat and all that..

IMG_9630

More importantly, I started experimenting with the weathering. First take a look at my kickass weathering mount setup!

IMG_9476 IMG_9475 IMG_9477

Once I had this on the inflatable ball, weathering was fun and easy. I must say this is a process I really do enjoy.

IMG_9478

This was only a test with water colours, soon the real weathering will follow, this time with acrylics!

In addition to this milestone, I also got around to making a new PSI, since I lost my old one. Putting it all together looks really nice too!

IMG_9631

Stay tuned… =)

 

By |2016-12-06T00:00:03+01:00October 20th, 2015|BB-8, Building|Comments Off on BB-8 progress

BB8 Dome nearing completion

I hurried putting my dome for BB-8 together for the Sci Fi convention in mid September. This included doing a quick (and not nearly good enough) paint job to just get the dome to some sort of colour.

IMG_8519 IMG_8528

The paint was too thick in places, and I had not had enough time to do a proper job concealing the joints. You can really see the joint on the left hand side of the picture quite clearly.

I also had no time to really let the paint dry before I hit it with the clear coat, so it all sort of blended together. Not to mention the ugly skirt..

To fix the skirt and the dome ring, I needed to print new parts, something I have done and are still in the process of assembling.

Paint job being botched (and no orange) aside, it still looked pretty cool!

IMG_8538

Not to mention the extreme close-up .. 2001 warning ahead:

IMG_8540

This got me through the Sci Fi convention, even though it was just a base.

Being back home, I sanded the clear coat and most of the paint off, worked over some of the problem areas with some putty filler, sanded again, and then applied 3 coats of spray filler, before sanding it down AGAIN with 400 grit sand paper to a very smooth finish, before I applied the white paint again. No more problem areas, and no more visible joints!

IMG_9098

Once the dome was white (again) and the paint had cured, I taped over the entire dome, and cut out the portions that was going to be orange, and then hit the dome with the brand new orange paint I had custom ordered.

Once cured, the dome looks GREAT!

IMG_9113

After the paint had cured properly, it was time to hit it with the clear coat.

IMG_9115 IMG_9116 IMG_9118

The dome feels incredibly smooth.

Time to buy a can of dark grey and tint the Radar Surrounds and the Holo Projector (and the Holo Projector ring) in the proper colour and mount them.

The only annoying thing is that I had made a really good PSI that should sit in the smaller hole on this picture, however, when cleaning out my workshop the other day, I suspect that small PSI that I wrote a nice blog post about, accidentally found its way out in the trash…

IMG_9081

Ah well, you gain some, you lose some. I have updated the 3D model for this, so next time it should be a lot easier for me to get what I need to get done!

Next up is putting some more focus on the dome ring and dome skirt so I can paint and mount them for a finalized dome structure. Can’t wait to get this part of the build done so I can start weathering the dome, I’m really looking forward to that!

By |2016-12-06T00:00:03+01:00October 7th, 2015|BB-8, Building|Comments Off on BB8 Dome nearing completion

Friction Welding to alter appearances

So, during this rather long and tedious 3D printing process to churn out parts for the BB-8, The 3D model has changed along the way, and as a result, some of my prints are no longer accurate.

I had a part of the “triangle” that holds the rounded panels together that changed recently, making 3 parts out of 6 obsolete.

IMG_9125

Now, these take a good 4 hours and some change to print, and I didn’t want to just waste 12+ hours on printing parts I didn’t need!

Looking at the specs, I realized that there is another part, that has the same basic construction as this (with overlaps and all) but does NOT have the groove that cuts out what is to be a panel in the finished full part.

Only thing I would need to do, is fill that groove that “splits” the part in two!

Sounds like a perfect job for some friction welding!

Friction welding, is really when you use friction to melt plastic together. I have used this on joints inside my R2, using round styrene rods that I put in my power drill, and then simply “drilled” until the plastic melted, and this created a very stable joint.

When doing this on a 3D print, I insert a piece of 1.75mm filament into my Dremel, and crank it up to about 80% speed, and gently push the quick rotating filament towards the area where I want to do the weld.

IMG_9126

As the quick rotating plastic melts, it also melts the surrounding plastic, making the new weld a part of the surrounding material.

First I did one softer go, to fill in as much of the groove as I can in one go..

IMG_9128

Then another go, that really pushes the materials inside, and also tried to erase the edges of the old groove, leaving a small extrusion of material after I am done.

IMG_9127

Now, this might not look pretty, but remember the plastic here is now part of the old print.

Using a break blade knife to first cut away some of the excess material, then using the same knife to scrape across the surface…

IMG_9133

.. and you end up with a groove that is totally gone.

Now, there are still some very small spots here and there, but compared to the layers of the print, they are nothing to worry about. Once I sand this part down properly and spray it with some spray filler, this will be completely invisible!

It only took about 4 minutes to do the three panels, and I saved up tons of time and filament compared to throwing the old pieces out and printing these from scratch!

By |2016-12-06T00:00:04+01:00October 7th, 2015|BB-8, Building|Comments Off on Friction Welding to alter appearances
Go to Top